IMPACT IDPU TELEMETRY FORMAT (SOH) NOTE: Bytes are swapped by the spacecraft/MOC: swap byte pairs before decoding packet! Revision: X 2005-Nov-17 IDPU SOH Start ApID 200 Total SOH Length= 272 OK Addressing IDENTIFIER Lng OFFSET TYPE WIDTH A1 A0 Units RL YL YH RH DESCRIPTION Module Mux Source Validity GSE Display Test Procedure UTCs 4 6 U2143 32 1 0 Sec UTC Seconds since epoch HKP IMPACT ICD 1 IDPU FSW_EXEC UTCf 2 10 U21 16 1.52588E-05 0 Sec UTC Seconds fraction (2^-16 sec) Time IMPACT ICD 1 IDPU FSW_EXEC ISampleTime 2 12 TIMEHMS 16 1 0 "Sample Time, Hours, Min, Sec (4,6,6 bits)" Time 1 IDPU FSW_EXEC ISoftwareVersion 1 14 UB 8 1 0 -1 19 256 256 Flight Software Version Number HKP 1 IDPU IHardwareVersion 1 15 UB 8 1 0 Hardware Version Number (FPGA) HKP 1 IDPU IPollTimeMax 2 16 U21 16 0.000032 0 Sec -1 0 0.8 1 Maximum foreground loop time Time 1 IDPU FSW_EXEC IPollTimeAvg 2 18 U21 16 0.000032 0 Sec -1 0 0.25 0.5 Average foreground loop time HKP 1 IDPU ITimeJitter 1 20 UB 8 LOGT 0 Sec -1 -1 0.001 1 Max UTC time jitter compared to SampleClock once a sec (see below) Time 1 IDPU IErrorCode 1 21 UB 8 1 0 Error Code UTIL 1 IDPU FSW_EXEC IErrorData 1 22 UB 8 1 0 Error Data UTIL 1 IDPU FSW_EXEC IErrorCount 1 23 UB 8 1 0 -1 -1 1 1 Error Count UTIL 1 IDPU FSW_EXEC ICommandCount 2 24 U21 16 1 0 IMPACT Command Counter Command 1 IDPU FSW_EXEC ICommandLastID 1 26 UB 8 1 0 "IMPACT Last Command Ap ID (Bits 8,6,5,4,3,2,1,0)" Command 1 IDPU FSW_CMD ICommandLastSeq 1 27 UB 8 1 0 IMPACT Last Command Sequence Counter (LSB) Command 1 IDPU PCommandCount 2 28 U21 16 1 0 PLASTIC Command Counter Command 1 IDPU PCommandLastID 1 30 UB 8 1 0 "PLASTIC Last Command Ap ID (Bits 8,6,5,4,3,2,1,0)" Command 1 IDPU PCommandLastSeq 1 31 UB 8 1 0 PLASTIC Last Command Sequence Counter (LSB) Command 1 IDPU IIMPACT_SSR 1 32 UB 8 1 0 % -1 -1 95 100 IMPACT SSR Fill level Status 1 IDPU FSW_CMD IPLASTIC_SSR 1 33 UB 8 1 0 % -1 -1 95 100 PLASTIC SSR Fill Level Status 1 IDPU FSW_CMD ISCStatus 1 34 UB 8 1 0 Spacecraft Status (see below) Status 1 IDPU FSW_LD IBootSelect 1 35 UB 8 1 0 -1 -1 4 256 "Boot Select (0-3=EEPROM to RAM, 4-7=EEPROM, else PROM)" System 1 IDPU FSW_LD ICodePage 1 36 UB 8 1 0 -1 0 64 64 "Code Page (0=PROM, 8-11=EEPROM0-3, 16=RAM, Else = Illegal)" HKP 1 IDPU FSW_CMD ICodePageStatus 1 37 UB 8 1 0 Code Page Status Bits (see below) EEPROM 1 IDPU FSW_CMD ICmdSeqRunning 1 38 UB 8 1 0 -1 30 33 256 Command Sequence # Running (>31 -> no sequence running) CmdSeq 2 IDPU FSW_CMD InterfaceEnables 1 39 UB 8 1 0 Instrument Interface Enables (see Below) System 1 IDPU ITelemEnables 2 40 U21 16 1 0 IMPACT Telemetry Enables (see below) System 1 IDPU PTelemEnables 2 42 U21 16 1 0 PLASTIC Telemetry Enables System 1 IDPU InterfaceActive 1 44 UB 8 1 0 Instrument Interface Active (see below) System 1 IDPU IMaxIMPACTQ 1 45 UB 8 1 0 -1 -1 24 32 Maximum IMPACT queue Depth Telem 1 IDPU IMaxPLASTICQ 1 46 UB 8 1 0 -1 -1 128 250 Maximum PLASTIC Queue Depth Telem 1 IDPU IIMPACTBitrate 1 47 UB 8 36.26666667 0 bps -1 2800 3500 4000 IMPACT Telemetry bit rate (1 minute average) Telem 1 IDPU IPLASTICBitrate 1 48 UB 8 36.26666667 0 bps -1 2800 3500 4000 PLASTIC Telemetry bit rate (1 minute average) Telem 1 IDPU Spare 5 49 FSW_CMD ICmdSeqMask 4 54 U4321 32 1 0 Command Sequence Mask (see below) CmdSeq 2 IDPU IBurstModeID 1 58 UB 8 1 0 -1 -1 256 256 Burst Parameter Table Mode ID Burst 2 Burst IBurstCurCriteria 1 59 UB 8 1 0 -1 -1 256 256 Burst Current Criteria Burst 2 Burst FSW_LD ISTEUDoorCount 1 60 UB 8 1 0 -1 -1 256 256 STE-U Door motion count STE 2 STEDoor ISTEUDoorStart 1 61 UB 8 0.125 0 sec -1 0 1.25 1.5 STE-U Time from power application to motion start STE 2 STEDoor ISTEUDoorDone 1 62 UB 8 0.125 0 sec -1 0 1.25 2 STE-U Time from power application to motion complete STE 2 STEDoor ISTEDDoorCount 1 63 UB 8 1 0 -1 -1 256 256 STE-D Door motion count STE 2 STEDoor ISTEDDoorStart 1 64 UB 8 0.125 0 sec -1 0 1.25 1.5 STE-D Time from power application to motion start STE 2 STEDoor ISTEDDoorDone 1 65 UB 8 0.125 0 sec -1 0 1.25 2 STE-D Time from power application to motion complete STE 2 STEDoor IAutoLUT 1 66 UB 8 1 0 SWEA/STE Auto LUT enables (see below) "SWEA/STE-D, STE-U" 2 SWEA/STE ISTEModeID 1 67 UB 8 1 0 -1 -1 256 256 STE LUT Table ID "SWEA/STE-D, STE-U" 2 STE ISWEAModeID 1 68 UB 8 1 0 -1 -1 256 256 SWEA LUT Table ID SWEA/STE-D 2 SWEA IBurstSavePage 1 69 UB 8 1 0 64 127 256 256 Burst recording page number Burst 2 Burst IBurstSendPage 1 70 UB 8 1 0 -1 127 256 256 Burst transmission page number Burst 2 Burst IBurstBestCriteria 1 71 UB 8 1 0 -1 -1 256 256 Burst Save Best Criteria Burst 2 Burst ISTEUA 0 72 STEU Analog Housekeeping IMagHKP 2 72 U21 16 1 0 MAG Hardware Housekeeping (see below) MAG MagInterface MAG #REF! IMAGHeater 2 74 U21 16 -0.03037 60.45 mA -2 -2 40 50 MAG sensor heater input current (on 28V primary) MAG 0 U-AFEPWR SWEA IMAGTemp 2 76 U21 16 MAG C -33 -20 35 40 MAG sensor temperature MAG 1 U-AFEPWR SWEA spare analog 2 78 U21 16 1 0 Spare STE-U interface analog 2 U-AFEPWR SWEA spare analog 2 80 U21 16 1 0 Spare STE-U interface analog 3 U-AFEPWR SWEA spare analog 2 82 U21 16 1 0 Spare STE-U interface analog 4 U-AFEPWR SWEA spare analog 2 84 U21 16 1 0 Spare STE-U interface analog 5 U-AFEPWR SWEA spare analog 2 86 U21 16 1 0 Spare STE-U interface analog 6 U-AFEPWR SWEA ISTEUCur 2 88 U21 16 -0.002462 4.982 V 2 5 30 40 "STE-U Front End Current (sum of +5A, -5A, and +5D). See below" STE-U 7 U-AFEPWR SWEA spare analog 2 90 U21 16 Spare STE-U interface analog 8 U-AFEPWR SWEA ISTEUTemp 2 92 U21 16 RTD C -110 -90 33 43 STE-U temperature (see below) STE-U 9 U-AFEPWR SWEA ISTEUDACTemp 2 94 U21 16 YSI C -30 -20 50 60 STE-U Interface PWB Temperature (see below) STE-U 10 U-AFEPWR SWEA ISTEUVCCA 2 96 U21 16 0.001254303 0.009000501 V 2.25 2.375 2.625 2.75 STE-U +2.5V Supply Voltage STE-U 11 U-AFEPWR SWEA ISTEU5VD 2 98 U21 16 0.002813721 0.020190414 V 4.5 4.75 5.25 5.5 STE-U +5V Digital Supply Voltage STE-U 12 U-AFEPWR SWEA ISTEUVCC1 2 100 U21 16 0.002813721 0.020190414 V 4.8 4.9 5.1 5.2 STE-U FPGA Interface +5V Supply voltage (ref) STE-U 13 U-AFEPWR SWEA ISTEU5VA 2 102 U21 16 0.002813721 0.020190414 V 4.5 4.75 5.25 5.5 STE-U +5V Analog Supply Voltage STE-U 14 U-AFEPWR SWEA ISTEU12V 2 104 U21 16 0.005137299 0.03686371 V 11.5 12.5 14 16 STE-U +12V Supply Voltage STE-U 15 U-AFEPWR SWEA ISWEAMCP 2 106 U21 16 -2.486 4982 V -20 2000 3000 4000 SWEA MCP Voltage SWEA/STE-D 0 D-AFEPWR SWEA ISWEANR5V 2 108 U21 16 -0.003812 7.468 V 4 4.5 6.7 7 SWEA Non-regulated HV Voltage 5V supply SWEA/STE-D 1 D-AFEPWR SWEA ISWEAAnal 2 110 U21 16 -0.4222 829.6 V -30 -25 750 800 SWEA Analyzer Voltage SWEA/STE-D 2 D-AFEPWR SWEA ISWEADefl1 2 112 U21 16 -0.8461 1663 V -30 -25 1500 1600 SWEA Defelector 1 Voltage SWEA/STE-D 3 D-AFEPWR SWEA ISWEADefl2 2 114 U21 16 -0.8461 1663 V -30 -25 1500 1600 SWEA Deflector 2 Voltage SWEA/STE-D 4 D-AFEPWR SWEA ISWEAV0 2 116 U21 16 0.01243 -24.91 V -25 -25 0.1 1 SWEA V0 Voltage SWEA/STE-D 5 D-AFEPWR SWEA ISWEAGND 2 118 U21 16 -0.002462 4.982 V -0.1 -0.05 0.05 0.1 SWEA Ground SWEA/STE-D 6 D-AFEPWR SWEA ISWEASTEDCur 2 120 U21 16 -0.002462 4.982 V -20 0 30 40 "SWEA/STE-D Front End Current (sum of +5A, -5A, and +5D). See below" SWEA/STE-D 7 D-AFEPWR SWEA ISWEAMCPTemp 2 122 U21 16 YSI C -40 -30 35 50 SWEA MCP Temperature (see below) SWEA/STE-D 8 D-AFEPWR SWEA ISTEDTemp 2 124 U21 16 RTD C -110 -90 33 43 STE-D temperature (see below) SWEA/STE-D 9 D-AFEPWR SWEA ISWEADACTemp 2 126 U21 16 YSI C -40 -30 35 50 SWEA PWB Temperature (see below) SWEA/STE-D 10 D-AFEPWR SWEA ISWEASTEDVCCA 2 128 U21 16 0.001254303 0.009000501 V 2.25 2.375 2.625 2.75 SWEA/STE-D +2.5V Supply Voltage SWEA/STE-D 11 D-AFEPWR SWEA ISWEASTED5VD 2 130 U21 16 0.002813721 0.020190414 V 4.50 4.75 5.25 5.50 SWEA/STE-D +5V Digital Supply Voltage SWEA/STE-D 12 D-AFEPWR SWEA ISWEASTEDVCC1 2 132 U21 16 0.002813721 0.020190414 V 4.8 4.9 5.1 5.2 SWEA/STE FPGA Interface +5V Supply voltage (ref) SWEA/STE-D 13 D-AFEPWR SWEA ISWEASTE5VA 2 134 U21 16 0.002813721 0.020190414 V 4.25 4.50 5.50 5.75 SWEA/STE-D +5V Analog Supply Voltage SWEA/STE-D 14 D-AFEPWR SWEA ISWEASTE12V 2 136 U21 16 0.005137299 0.03686371 V 10.8 11 12.6 13.2 SWEA/STE-D +12V Supply Voltage SWEA/STE-D 15 D-AFEPWR SWEA ISTEUDig 2 138 U21 16 1 0 STE-U digital housekeeping (see below) STE-U SIF05 STEUInterface STEU #REF! ISWEASTEDDig 2 140 U21 16 1 0 SWEA/STE-D digital housekeeping (see below) SWEA/STE-D SIF05 SWEAInterface SWEA #REF! BLK_ID 1 142 8 Block ID PLASTIC PLASTICInterface PLASTIC #REF! DEV_ID 1 143 8 Device ID PLASTIC PLASTICInterface PLASTIC #REF! PLASTIC 0 144 PLASTIC housekeeping (128 bytes) PLASTIC PLASTICInterface PLASTIC #REF! PLRNM_SPARE 2 144 U21 16 0.000152579 0.00742664 PLASTIC spare PLASTIC PLASTICInterface PLASTIC #REF! PLVC_-12V 2 146 U21 16 -0.000228713 -0.011132356 V -13.5 -13.0 -11.8 -11.5 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_-5V 2 148 U21 16 -0.000152579 -0.00742661 V -5.5 -5.3 -4.7 -4.4 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PESA_VM_POS 2 150 U21 16 0.1602 29.084 V 6000 6100 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_1_VM 2 152 U21 16 0.1501 10.644 V 6800 6900 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_1_TAP 2 154 U21 16 0.1503 9.7289 V 3100 3200 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_2_VM 2 156 U21 16 0.1506 10.731 V 6800 6900 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_2_TAP 2 158 U21 16 0.15 10.087 V 3100 3200 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+2.5VB 2 160 U21 16 0.000152681 -0.045011681 V 2.33 2.38 2.50 2.60 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PPAC_CM_DC 2 162 U21 16 0.000152639 -0.043288457 mA 55 70 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+12V 2 164 U21 16 0.000228885 -0.057173689 V 11.5 11.8 13.4 13.8 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLRPM_SPARE 2 166 U21 16 0.000152681 -0.045011756 PLASTIC spare PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+2.5VA 2 168 U21 16 0.000152681 -0.045011756 V 2.33 2.38 2.50 2.60 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+5V 2 170 U21 16 0.000152681 -0.045011756 V 4.70 4.90 5.30 5.50 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PADC_AVDD 2 172 U21 16 0.000152681 -0.045011756 V PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PADC_DVDD 2 174 U21 16 0.000152681 -0.045011756 V PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PPAC_VM 2 176 U21 16 -0.5931 248.28 V -27000 -25000 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PCAL_VREF 2 178 U21 16 0.000152639 -0.043291815 V 4.8 4.9 5.1 5.2 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PPAC_CM_AC 2 180 U21 16 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PMCP_VM 2 182 U21 16 0.1436 -807.4 V 3400 3800 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PMCP_CM_DC 2 184 U21 16 0.000152639 -0.043291815 mA 60 75 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PMCP_CM_AC 2 186 U21 16 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_CM_DC 2 188 U21 16 0.000152639 -0.043291815 mA 170 190 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PS_CH_VM 2 190 U21 16 -0.0149 27.843 V -5100 -5000 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PS_CH_VM_TAP 2 192 U21 16 -0.1499 29.732 V -3500 -3400 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PS_CH_CM_DC 2 194 U21 16 0.000152681 -0.045011756 mA 17 19 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PESA_VM_NEG 2 196 U21 16 -0.1594 10.243 V -6100 -6000 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PESA_CM_DC 2 198 U21 16 0.001737088 3.670901532 mA 65 70 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_1_CM_DC 2 200 U21 16 0.000152681 -0.045011756 mA 15 30 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDFL_2_CM_DC 2 202 U21 16 0.000152681 -0.045011756 mA 15 30 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+2.5VB_IMON 2 204 U21 16 0.011352671 -33.97854345 mA 35 70 370 400 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+12V_IMON 2 206 U21 16 0.015414971 -21.87538537 mA 50 100 500 600 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_-12V_IMON 2 208 U21 16 0.001974763 15.44659255 mA 5 10 110 130 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+5V_IMON 2 210 U21 16 0.011285408 -91.69958244 mA 25 50 400 500 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_-5V_IMON 2 212 U21 16 0.002418321 4.160963459 mA 40 60 120 150 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLVC_+2.5VA_IMON 2 214 U21 16 0.007382798 -34.95385751 mA 20 35 300 330 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_VM 2 216 U21 16 0.000304999 -0.047344984 V PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PPLUG_ID 1 218 UB 8 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PADC_LU_FLAG 1 219 UB 8 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDAC_STATUS 1 220 UB 8 1 0 PLASTIC DAC Board Status PLASTIC PLASTICInterface PLASTIC #REF! PADC_LU_CTR 1 221 UB 8 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PDHK_SPARE 2 222 U21 16 1 0 PLASTIC spare PLASTIC PLASTICInterface PLASTIC #REF! PADC0_AGND 1 224 PADC1_AGND 1 225 PRA_E0 1 226 UB 8 0.0108 -0.0138 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PRA_E1 1 227 UB 8 0.0108 -0.0138 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PTAC0_TSP 1 228 UB 8 1.6786 -342.43 C -20 -10 38 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PTAC2_TSP 1 229 UB 8 1.6786 -342.43 C -20 -10 38 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PSB0_TSP 1 230 UB 8 1.6786 -342.43 C 38 40 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSB1_TSP 1 231 UB 8 1.6786 -342.43 C 38 40 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PTOF_HV0_TSP 1 232 UB 8 1.6786 -342.43 C -20 -10 35 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PTOF_HV1_TSP 1 233 UB 8 1.6786 -342.43 C -20 -10 35 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PS_C_0_TSP 1 234 UB 8 1.6786 -342.43 C -20 -10 35 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PS_C_1_TSP 1 235 UB 8 1.6786 -342.43 C -20 -10 35 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PLVC0_TSP 1 236 UB 8 1.6786 -342.43 C -20 -10 38 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PLVC1_TSP 1 237 UB 8 1.6786 -342.43 C -20 -10 38 42 PLASTIC PLASTIC 1.6786 -342.43 PLASTICInterface PLASTIC #REF! PADC0_VREF 1 238 UB 8 0.0108 -0.0138 V 1 1.2 1.43 1.53 PADC1_VREF 1 239 UB 8 0.0108 -0.0138 V 1 1.2 1.43 1.53 PSSD_STATUS 2 240 U21 16 1 0 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_V_POS_ANALOG 2 242 U21 (only 10 bits used) 16 0.0093 -0.986 V 7 7.2 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_V_NEG_ANALOG 2 244 U21 (only 10 bits used) 16 -0.0091 1.127 V -7.2 -7 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_HV_BIAS 2 246 U21 (only 10 bits used) 16 0.1575 -4.094 V 100 110 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PSSD_TC0 2 248 U21 (only 10 bits used) 16 0.4032 -300.57 C -20 -10 29 36 PLASTIC PLASTIC 0.4032 -300.57 PLASTICInterface PLASTIC #REF! PSSD_TC1 2 250 U21 (only 10 bits used) 16 0.4032 -300.57 C -20 -10 29 36 PLASTIC PLASTIC 0.4032 -300.57 PLASTICInterface PLASTIC #REF! PSSD_TC2 2 252 U21 (only 10 bits used) 16 0.4 -298.35 C -20 -10 29 36 PLASTIC PLASTIC 0.4 -298.35 PLASTICInterface PLASTIC #REF! PSSD_V_POS_DIG 2 254 U21 (only 10 bits used) 16 0.0082 0.1753 V 4.5 5 6 6.5 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! PLASTICtbd 14 256 PLASTIC PLASTIC PLASTICInterface PLASTIC #REF! Spare 1 270 Checksum 1 271 UB Sum of all 272 packet bytes should equal zero. SYSTEM 1 Total Bytes 266 272 <==OK "Note on Validity: 1=Allways, 2=After boot (ISoftwareVersion >19)" D-AFEPWR =InterfaceActive bit SWEAInterface=1 AND ISWEASTEDDig bit AFEPWR=1 U-AFEPWR =InterfaceActive bit STEUInterface=1 AND ISTEUDig bit AFEPWR=1 Identifier Bit Contains Else use indicated InterfaceActive bit ICodePageStatus: 7 "EEPROM Code Page 3 checksum status (1=bad, RED; 0=OK)" "When not Valid, set color=blue, no limit checking." 6 "EEPROM Code Page 2 checksum status (1=bad, RED; 0=OK)" 5 "EEPROM Code Page 1 checksum status (1=bad, RED; 0=OK)" 4 "EEPROM Code Page 0 checksum status (1=bad, RED; 0=OK)" 3 "RAM Code Page checksum status (1=bad, RED; 0=OK)" 2:0 "RAM Code Page Source: 0-3 = copies of EEPROM Code Pages, 7=PROM, 6=modified" ISpacecraftStatus 0 "IDPU Power Warning, (1=Warning, RED; 0=OK)" 1 "SEP Power Warning, (1=Warning, YELLOW; 0=OK)" 2 "SWEA Power Warning, (1=warning, YELLOW; 0=OK)" 3 "PLASTIC Power Warning, (1=warning, YELLOW; 0=OK)" 4 "Thruster Warning, (1=warning, YELLOW; 0=OK)" 5 "Coarse Pointing, (1=Bad Pointing, YELLOW; 0=OK)" 6 "SWAVES Power Warning (1=warning, YELLOW; 0=OK)" 7 "1553 Channel spacecraft status was received on, 1=A, 0=B" IMagHKP 0:3 "Mag Error counter (not 0 = RED, else OK)" 4:7 Mag Command counter 8 "spare, =1 (0=Red; 1=OK)" 9 First (1st MAG sample after 1Hz tic) 10 Time (toggles at 1Hz) 11 Interface Parity Error (1=RED; 0=OK) 12 Interface Timeout error (1=RED; 0=OK) 13 "ADC Cal (0=off, 1=on)" 14 "In Flight Cal (0=off, 1=on)" 15 "Range (0=low fields, high sensitivity, 1=high fields, low sensitivity)" ISTEUDig 0 CPE "Command Interface Parity Error (1=Error, RED; 0=OK)" 1 AFEPWR AFE Power status (1=on; 0=OFF=YELLOW) 2 AFESHDN AFE Over-current detect (1=overcurrent=RED; 0=OK) 3 x 5:4 STECOVSTAT "STE Cover Status:(00=illegal, RED; 01=Closed; 10=Open; 11=Moving, YELLOW)" 7:6 STECOVSW "STE Cover Actuator Power (00=OFF; 01=Open; 10=Close; 11=Illegal, RED)" 8 ANORM "Indicates an anusual configuration, (0=Normal; 1=Unusual, YELLOW)" 9 x 10 x 11 HSKPMD "Analog Housekeeping mode (0=cycling, 1=sweep)" 12 ENBSTETP "Enable STE Test Pulser (1=enabled, YELLOW; 0=disabled)" 13 x 14 ENBSWEA "Enable SWEA Subsystem (1=enabled, RED; 0=disabled)" 15 PCE "Protected Command Error (1=error, RED; 0=OK)" ISWEASTEDDig 0 CPE "Command Interface Parity Error (1=Error, RED; 0=OK)" 1 AFEPWR AFE Power status (1=on; 0=OFF=YELLOW) 2 AFESHDN AFE Over-current detect (1=overcurrent=RED; 0=OK) 3 SWEACOVSTAT "SWEA cover status, (1=closed, YELLOW; 0=open)" 5:4 STECOVSTAT "STE Cover Status:(00=illegal, RED; 01=Closed; 10=Open; 11=Moving, YELLOW)" 7:6 STECOVSW "STE Cover Actuator Power (00=OFF; 01=Open; 10=Close; 11=Illegal, RED)" 8 ANORM "Indicates an anusual configuration, (0=Normal; 1=Unusual, YELLOW)" 9 MCPHVENB "MCP HV Enable (0=disabled, 1=enabled)" 10 NRHVENB "Non-regulated HV Enable (0=disabled, 1=enabled)" 11 HSKPMD Analog Housekeeping mode (0=cycling; 1=sweep) 12 ENBSTETP "Enable STE Test Pulser (1=enabled, YELLOW; 0=disabled)" 13 ENBSWEATP "Enable SWEA Test Pulser (1=enabled, YELLOW; 0=disabled)" 14 ENBSWEA "Enable SWEA Subsystem (1=enabled; 0=disabled, RED)" 15 PCE "Protected Command Error (1=error, RED; 0=OK)" InterfaceEnables 0 MAGInterface "MAG Instrument Interface Enable (1=enabled; 0=disabled, YELLOW)" 1 STEUInterface "STE-U Instrument Interface Enable (1=enabled; 0=disabled, YELLOW)" 2 SWEAInterface "SWEA/STE-D Instrument Interface Enable (1=enabled; 0=disabled, YELLOW)" 3 SEPInterface "SEP Instrument Interface Enable (1=enabled; 0=disabled, YELLOW)" 4 PLASTICInterface "PLASTIC Instrument Interface Enable (1=enabled; 0=disabled, YELLOW)" 5 spare 6 EEPROMWriteEnable IDPU EEPROM Write Enable (1=enabled=YELLOW; 0=disabled) 7 PLASTICSysCmd "PLASTIC System Commands Enable (1=enabled, YELLOW; 0=disabled)" InterfaceActive 0 MAGInterface "MAG Instrument Interface Active (1=active; 0=inactive, YELLOW)" 1 STEUInterface "STE-U Instrument Interface Active (1=active; 0=inactive, YELLOW)" 2 SWEAInterface "SWEA/STE-D Instrument Interface Active (1=active; 0=inactive, YELLOW)" 3 SEPInterface "SEP Instrument Interface Active (1=active; 0=inactive, YELLOW)" 4 PLASTICInterface "PLASTIC Instrument Interface Active (1=active; 0=inactive, YELLOW)" 5 SWAVESInterface "SWAVES RT-RT Instrument Interface Active (1=active, 0=inactive, YELLOW)" 6 SWAVESTimeout "SWAVES RT-RT Rx Timeout; SWAVES not responding. (1=Timeout=YELLOW, 0=OK)" 7 SEPTimeout "SEP Interface activity low for too long (1=Timeout=Yellow, 0=OK)" ITelemEnables 0 BurstTlm "Enable Burst Telemetry to be sent (for all ITelemEnables except where otherwise stated, 0=disabled, YELLOW; 1=enabled)" 1 SEPTlm Enable SEP Telemetry 2 MAGTlm Enable MAG Telemetry 3 MAGBurst Enable MAG Burst Collection 4 STERatesTlm Enable STE Monitor Rates Telemetry 5 STERatesBurst Enable STE Monitor Rates Burst Collection 6 STESpecTlm Enable STE Spectra Telemetry 7 STESpecBurst Enable STE Spectra Burst Collection 8 SWEADistTlm Enable SWEA Distribution Telemetry 9 SWEADistBurst Enable SWEA Distribution Burst Collection 10 SWEAPADTlm Enable SWEA PAD Telemetry 11 SWEAMomTlm Enable SWEA Moments Telemetry 12 SWEAFHKP "Enable SWEA Fast Housekeeping (no alarm state, 0 or 1 = green)" 13 SWEASpecTlm Enable SWEA Spectra Telemetry 14 BurstCriteria Enable Burst Criteria Telemetry 15 SWEAMomComp Enable SWEA Moment computation IAutoLUT 0 ISWEAAutoLUT Enable SWEA Auto LUT Generation (1=manual) 1 ISTEAutoLUT Enable STE Auto LUT Generation (1=manual) 2 ISWEAAutoV0 Enable automatic generation of SWEA V0 setting (1=manual) 3 ISWEAMomE Enable automatic generation of SWEA Moment energy coef (1=manual) 4 spare 5 ISTEULUT Current state of the STE-U LUT page select 6 ISTEDLUT Current state of the STE-D LUT page select 7 ISWEALUT Current state of the SWEA LUT page select ICmdSeqMask 31 0: IDPUPwrWarn IDPU Power Warning Sequence Enable 30 1: IDPUPwrWarnClr IDPU Power Warning Clear Sequence Enable 29 2: SEPPwrWarn SEP Power Warning Sequence Enable 28 3: SEPPwrWarnClr SEP Power Warning Clear Sequence Enable 27 4: SWEAPwrWarn SWEA Power Warning Sequence Enable 26 5: SWEAPwrWarnClr SWEA Power Warning Clear Sequence Enable 25 6: PLAPwrWarn PLASTIC Power Warning Sequence Enable 24 7: PLAPwrWarnClr PLASTIC Power Warning Clear Sequence Enable 23 8: ThrusterWarn Thruster Warning Sequence Enable 22 9: ThrusterWarnClr Thruster Warning Clear Sequence Enable 21 10: PointWarn Coarse Pointing Warning Sequence Enable 20 11: PointWarnClr Coarse Pointing Warning Clear Sequence Enable 19 12: SEPRecovery SEP Recovery Sequence Enable 18 Seq13 Command Sequence 13 Enable 17 Seq14 Command Sequence 14 Enable 16 Seq15 Command Sequence 15 Enable 15 Seq16 Command Sequence 16 Enable 14 Seq17 Command Sequence 17 Enable 13 Seq18 Command Sequence 18 Enable 12 Seq19 Command Sequence 19 Enable 11 20: PLA_PS0 "PLASTIC PS 0 (Disable Entrance system; ""Thruster/Coarse"") - Sequence Enable" 10 21: PLA_Start PLASTIC Startup Sequence Enable 9 22: PLA_PS1 PLASTIC PS 1 (Reduce HV levels) Sequence Enable 8 23: PLA_PR0 "PLASTIC PR0 - (second half, recover from a ""PAC DISCHARGE"") Sequence Enable" 7 24: PLA_PS2 "PLASTIC PS2 (Disable entrance system, turn off HV, don't request turnoff ""PAC Discharge"") Sequence Enable" 6 Seq25 Command Sequence 25 Enable 5 26: PLA_PR0 "PLASTIC PR0 (part 1 - enbale entrance system, bring up HVs and put system in mode 3; after PS2) Sequence Enable" 4 27: PLA_PR1 "PLASTIC PR1 (enable entrance system, Run if Thruster Coarse bits clear) Sequence Enable" 3 Seq28 Command Sequence 28 Enable 2 29: PLA_PS3 "PLASTIC PS3 (disable Entrance system, turn off HV and requenst PLASTIC OFF; ""IDPU/PLASTIC pwr down"") Sequence Enable" 1 30: UserPeriodic User Periodic Sequence Enable 0 31: SystemPeriodic System Periodic Sequence Enable Temperature Conversions (YSI and RTD) YSI Temp = A + B*ADC + C*ADC^2 + D*ADC^3 + E*ADC^4 + F*ADC^5 A 1.3063E+02 Example B -3.2163E-01 ADC Temp C 4.8397E-04 1024 23.69 D -4.0961E-07 E 1.6780E-10 F -2.6422E-14 RTD Temp = A + B*ADC + C*ADC*ADC A -244.7 Example B 0.100925 ADC Temp C 1.004E-05 2200 25.92 MAG Temp = A + B*ADC + C*ADC^2 + D*ADC^3 + E*ADC^4 + F*ADC^5 A 6.7051E+01 Example B -5.7333E-02 ADC Temp C 3.7342E-05 1024 31.91 D -1.9096E-08 E 5.0166E-12 F -5.2833E-16 LOGT Conversion Convert 8 bit to 19 bit using log compression scheme. Units are seconds/2^16 (multiply un-compressed value by 2^-16 to get seconds) ISWEASTEDCur and ISTEUCur conversions "The above conversions get you a measurement of the trip voltage setting. To convert that to current (sum of +5.1V current and -5.1V current, mA) use:" ISWEASTEDCur-corrected = STEDa*V + STEDb*ISWEASTE12V) - STEDc*(ISWEASTEDVCC1 - ISWEASTED5VD) ISTEUCur-corrected = STEUa*V + STEUb*ISTEU12V) - STEUc*(ISTEUVCC1-ISTEU5VD) STEUa 40.20 STEUb 16.14 STEUc 201.00 Example STEDa 40.20 V -4.70 STEDb 16.14 ISTEU12V 13.10 STEDc 201.00 ISTEUVCC1 4.98 ISTEU5VD 4.98 Current 22.15